You are here: Home > Handout > Metal Cutting Processes 1 - Turning
Metal Cutting Processes 1 - Turning
This training module is designed to give you 'hands-on' experience through which you can gain a good appreciation of this well-known type of machine tool. In particular your attention will be directed towards its operational uses and parameters, the general layout of controls, accessories, associated tooling, and the maintenance factors related to lathes.
In order that you can make the most use of the limited time available on lathes it is essential that you use every chance to consolidate what you observe. This type of work is largely self-motivated and the drive and desire to find out must come from you.
It takes a considerable time to become a skilled lathe operator and to possess all the skill of hand that goes with it. Therefore it is not expected that you will be manually skilled on completion of the module but you will have gained intellectually and without doubt, by practical involvement, some skill of hand will be achieved.
Figure 1. Example of a Typical Centre Lathe
2. Centre Lathe
The term Centre Lathe is derived from the fact that in its operation the lathe holds a piece of material between two rigid supports called centres, or by some other device such as a chuck or faceplate which revolves about the centre line of the lathe.
The lathe shown above is a typical example. This machine is usually used in a jobbing (one off) situation or for small batch work where it would be too expensive to specially 'tool up' for just a few items.
The lathe on which you will work is a machine used to cut metal. The spindle carrying the work is rotated whilst a cutting tool, which is supported in a tool post, is made to travel in a certain direction depending on the form of surface required. If the tool moves at right angles to the axis of the rotation of the work it produces a flat surface as in (a) , whilst if it moves parallel to this axis a cylindrical surface is produced as in (b).
(b) Parallel Turning
3. Cutting Tools
The tool used in a lathe is known as a single point cutting tool. It has one cutting edge or point whereas a drill has two cutting edges and a file has numerous points or teeth.
The lathe tool shears the metal rather than cuts as will be seen later and it can only do so if there is relative motion between the tool and the workpiece. For example, the work is rotating and the tool is moved into its path such that it forms an obstruction and shearing takes place. Of course the amount of movement is of paramount importance - too much at once could for instance result in breakage of the tool.
The type and design of the tools selected will depend on the job in hand, the machining operation selected and the material to be cut. The correct tool especially the various face angles are essential if the operation is to be done in a cost-effective (i.e. productive) way. The tools used in a lathe are various, some of which are shown in figure 3.
The range of cutting tool types is extensive and a few examples only are shown in this handout. Nonetheless you should take every opportunity to look deeper into the types of tools available.
5. Tool Angles
There are three important angles in the construction of a cutting tool rake angle, clearance angle and plan approach angle.
Figure 5. Main Features of a Single Point Cutting Tool
Rake angle is the angle between the top face of the tool and the normal to the work surface at the cutting edge. In general, the larger the rake angle, the smaller the cutting force on the tool, since for a given depth of cut the shear plane AB, shown in Figure 4 decreases as rake angle increases. A large rake angle will improve cutting action, but would lead to early tool failure, since the tool wedge angle is relatively weak. A compromise must therefore be made between adequate strength and good cutting action.
Table 1. Typical value for top rake angle
Clearance angle is the angle between the flank or front face of the tool and a tangent to the work surface originating at the cutting edge. All cutting tools must have clearance to allow cutting to take place. Clearance should be kept to a minimum, as excessive clearance angle will not improve cutting efficiency and will merely weaken the tool. Typical value for front clearance angle is 6~10 degree in external turning.
Plan Profile of Tool
The trailing edge of the tool is ground backwards to give clearance and prevent rubbing and a good general guide is to grind the trailing edge at 90° to the cutting edge. Thus the Trail Angle or Relief Angle will depend upon the approach angle.
A small nose radius on the tool improves the cutting and reduces tool wear. If a sharp point is used it gives poor finish and wears rapidly.
6. Characteristics of Tool Material
For efficient cutting a tool must have the following properties:
Strength and Resistance to Shock
Low Coefficient of Friction
7. Tool Materials in Common Use
High Speed Steel (H.S.S.)
8. Tool life
As a general rule the relationship between the tool life and cutting speed is
VTn = C
For high-speed steel tools the
value of C ranges from 0.14 to 0.1 and for carbide tools the value would
9. Chip Formation & Chip Breaker
The type of chip produced depends on the material being machined and the cutting conditions at the time. These conditions include the type of tool used tool, rate of cutting condition of the machine and the use or absence of a cutting fluid.
A chip breaker is used to break the continuous chip into sections so that the chips cannot tangle around the cutting tool. The simplest form of chip breaker is made by grinding a groove on the tool face a few millimeters behind the cutting edge.
10. Cutting Speed & Feed
As you proceed to the process of metal cutting, the relative `speed' of work piece rotation and `feed' rates of the cutting tool coupled to the material to be cut must be given your serious attention. This relationship is of paramount importance if items are to be manufactured in a cost-effective way in the minimum time, in accordance with the laid down specifications for quality of surface finish and accuracy. You, as a potential supervisory / management level engineer, must take particular note of these important parameters and ensure that you gain a fundamental understanding of factors involved.
All materials have an optimum Cutting Speed and it is defined as the speed at which a point on the surface of the work passes the cutting edge or point of the tool and is normally given in meters/min. To calculate the spindle Speed required,
Table 2 shows the cutting speed recommended for some common metals. It may be possible to exceed these speeds for light finishing cuts. For heavy cuts they should be reduced.
Table 2. Cutting Speed
The term `feed' is used to describe the distance the tool moves per revolution of the workpiece and depends largely on the surface finish required. For roughing out a soft material a feed of up to 0.25 mm per revolution may be used. With tougher materials this should be reduced to a maximum of 0.10 mm/rev. Finishing requires a finer feed then what is recommended.
11. Cutting Fluid & Lubricant
The aims in metal cutting are to retain accuracy, to get a good surface finish on the workpiece and at the same time to have a longer tool life.
However during the metal cutting process heat is generated due to:
Heat generated due to friction can readily be reduced by using a lubricant. Heat caused by deformation cannot be reduced and yet it can be carried away by a fluid. Thus the use of a cutting fluid will serve to reduce the tool wear, give better surface finish and a tighter dimensional control.
The proper selection, mixing and application of cutting fluids is however often misunderstood and frequently neglected in machining practice. In order that the cutting fluid performs its functions properly it is necessary to ensure that the cutting fluid be applied directly to the cutting zone so that it can form a film at the sliding surfaces of the tool.
Cutting fluids in common use
There are many different forms of screw thread, Fig 11 shows the 'sections' of three most common types.
More types and specifications of screw threads can be found in any Workshop Technology Hand Books and you must get used to finding such information and knowing how to apply it.
Lathes are normally robust in construction and they will, with good care, last for many years. It is not unusual for instance to see good lathes still in uses that are 50 years old. To ensure good, accurate, trouble free use it is necessary that the correct maintenance routines are regularly carried out and that important surfaces such as slide-ways are kept well protected so as to reduce wear and thus maintain good accuracy. This aspect of 'good husbandry' should be of interest to you and you will be expected to demonstrate an understanding of this. In this respect the types of maintenance routine carried out, the design and accessibility of the maintenance system, and the lubricants used, are all factors that require your attention.